Best Electric Radiant Floor Heating for Tile Baths

The best electric radiant floor heating kit here is the LuxHeat 60 sqft system, because it pairs 720 watts of cable at 12 W/sqft with a Prova Flex-Heat uncoupling membrane that also handles waterproofing and crack isolation under tile. If you want app control instead, the 50 sqft LuxHeat with the UWG5 WiFi thermostat is the runner-up. Both run on 120 V and share the same 12 W/sqft output.

Best electric radiant floor heating at a glance

How I narrowed five kits down to a ranking

I compared the published specifications side by side, then mapped each kit to the buyer most likely to install it. Every kit in this set runs on 120 V, and every kit outputs 12 W per square foot, which is the standard for residential tile-warming under a bathroom or entry. The differences that decide a purchase are not watts. They are what sits between the cable and the tile, and what sits on the wall.

Three criteria carried the ranking:

1. Subfloor system. A loose cable laid with a membrane is not the same install as a peel-and-stick mat. One buys crack isolation, the other buys speed.
2. Thermostat capability. Basic touchscreen, WiFi, dual air-and-floor sensor.
3. Coverage match. A 15 sqft kit is not a small version of a 100 sqft kit. It is a different job.

I ignored colour, and I ignored the marketing language on the listings. A kit that publishes its cable length, its amp draw and its model number gives you enough to plan a circuit. A kit that publishes only the square footage does not.

Cable-and-membrane or peel-and-stick mat?

This is the question the category turns on, and most guides skip it.

• Loose cable with an uncoupling membrane. The two LuxHeat kits use Prova Flex-Heat membrane, and LuxHeat describes it as a three-in-one layer that adds crack prevention, waterproofing and load support beneath the tile. You weave the cable through the membrane pockets at 3-inch spacing. Slower, but the membrane is doing structural work as well as holding the cable.
• Pre-spaced mat. The BLARALA and VEVOR kits are mats: cable already fixed to a mesh or adhesive backing at fixed spacing. BLARALA states 19.69-inch-wide mat sections that can be cut, flipped or rotated. VEVOR states 2-inch spacing on a mat with double-sided adhesive to the subfloor. Faster to lay, but the mat is not a waterproofing or crack-isolation layer, so a wet bathroom still needs one added underneath.
• Loose cable, no membrane. The Warming Systems 15 sqft kit is 60 linear feet of cable on a spool with cable guides spaced roughly 3 inches apart. You supply the isolation layer.

If your subfloor is a wood-framed second-storey bathroom, the membrane path is the safer default because tile assemblies over wood want an isolation layer whether the floor is heated or not. If you're going over a slab in a first-floor entryway, a mat gets you laying tile the same afternoon.

What the thermostat actually decides

Every kit here bundles a thermostat, and it is worth paying attention to which one, because it is the single component you interact with every day.

The 60 sqft LuxHeat ships with the OJ Microline UDG4-4999, a touchscreen programmable head with GFCI. It is a wall-panel-only unit. The 50 sqft LuxHeat steps up to the UWG5, the same OJ Microline platform but with WiFi, described in the listing as 120 V, 15 A, with Class A GFCI. That is the same UWG5 head that Warming Systems bundles with its 15 sqft budget kit, and Warming Systems says it also has Bluetooth alongside the WiFi.

BLARALA's thermostat is programmable with four operating modes, and the listing says it uses dual air and floor sensors, a child lock, and overheat protection. VEVOR's is a touchscreen with built-in GFCI and a 14 to 113°F range.

Two takeaways. First, if app control matters to you, the runner-up LuxHeat and the budget Warming Systems kit are the only two with the WiFi UWG5. Second, dual sensors are worth asking for on a mat under stone or thick tile, because the air sensor keeps the room comfortable while the floor sensor keeps the cable from cooking a grout line.

1. LuxHeat 60sqft Electric Radiant Floor Heating System — Best overall

A 60 sqft cable kit with a Prova Flex-Heat membrane that doubles as waterproofing and crack isolation under tile.

Best for: a tiled bathroom where the subfloor needs waterproofing and crack isolation Skip it if: you want WiFi control from your phone

This is the kit I'd default to for a mid-sized bathroom in tile. LuxHeat publishes the full electrical picture: 240 ft of cable, 120 V, 6.0 A, 720 W, laid at 3-inch spacing for 12 W/sqft over 60 sqft. That is the standard density for residential floor warming, and the amp draw is low enough to share a bathroom circuit in many jurisdictions, though your electrician makes that call.

The reason it takes the top spot is not the cable itself. It is the Prova Flex-Heat membrane, which LuxHeat describes as a three-in-one layer providing crack prevention, waterproofing and load support. Under a shower-adjacent tile floor, that saves a separate uncoupling or waterproofing membrane. The bundled OJ Microline UDG4 is a touchscreen programmable thermostat with GFCI. It is wall-only, and that's the trade-off: you lose the WiFi feature the runner-up ships with.

Pros:

• 720 W over 60 sqft at 12 W/sqft
• Prova Flex-Heat membrane included
• 240 ft of cable, low 6.0 A draw
• UDG4 touchscreen thermostat with GFCI
• Full electrical specs published

Cons:

• No WiFi on the UDG4 thermostat
• Slower to install than a peel-and-stick mat
• No published warranty in the listing

2. LuxHeat 50sqft Electric Radiant Floor Heating System — Runner-up

The same membrane system as the winner, in a 50 sqft size with the WiFi UWG5 thermostat instead of the UDG4.

Best for: smaller tiled rooms where WiFi thermostat control matters Skip it if: you need more than 50 sqft of coverage

The runner-up is the sibling to the winner. Same Prova Flex-Heat three-in-one membrane, same 120 V cable at 12 W/sqft, same 3-inch spacing. What changes is the size and the thermostat. This kit ships 200 ft of cable, 5.0 A, 600 W, sized for 50 sqft. And instead of the UDG4, LuxHeat bundles the UWG5 LED touch WiFi programmable thermostat, described in the listing as 120 V, 15 A with Class A GFCI.

So why is this the runner-up and not the winner? Coverage. A typical mid-sized bathroom is closer to 55 to 65 sqft of heated area once you subtract the vanity and the toilet base, and the 60 sqft kit gives you more room to route the cable around fixtures. The 50 sqft kit is the right pick if your heated area is genuinely small, or if the WiFi thermostat is a hard requirement. Both are true for a lot of first-floor half-baths.

Pros:

• UWG5 WiFi touchscreen thermostat
• Same Prova Flex-Heat membrane as the winner
• 200 ft of cable, 5.0 A draw
• Class A GFCI protection
• 120 V, no dedicated wiring changes

Cons:

• 50 sqft caps out sooner than the 60 sqft kit
• No published warranty in the listing
• Requires a router within WiFi range of the thermostat

3. BLARALA Electric Radiant Floor Heating System — Best for pros

A 100 sqft peel-and-cut mat with dual sensors and a programmable head, sized for a full bathroom or a large entryway.

Best for: a larger bathroom where a cuttable mat speeds the install Skip it if: your subfloor is cracked or wood-framed and flexes

At 100 sqft, this is the largest kit here, and it is a mat rather than a loose cable. BLARALA lists the mat as 19.69 inches wide by 65.62 feet long, rated at 12 W/sqft, drawing 10.0 A at 120 V. The kit weighs 13.3 lb, model UHM-40, and BLARALA says the cables are CSA-certified and safe for wet locations. The mat can be cut, flipped or rotated to fit around fixtures, which is what makes it the fast install.

The thermostat is where BLARALA earns the pro label. The listing describes built-in GFCI, four operating modes, dual air and floor sensors, child lock and overheat protection. Dual sensors are the useful upgrade: the floor sensor keeps the cable temperature in check while the air sensor governs comfort. A trade-off comes with the mat format. It is not a waterproofing layer and it is not an uncoupling layer, so a wet floor over wood framing still needs a separate isolation membrane below.

Pros:

• 100 sqft mat covers a full bathroom
• Cuttable and flippable around fixtures
• Dual air and floor sensors
• Child lock and overheat protection
• CSA-certified for wet locations, per the listing

Cons:

• No membrane included for crack isolation
• Higher 10.0 A draw may want a dedicated circuit
• Sells more slowly than the smaller kits here

4. VEVOR Floor Heating Mat — Best for beginners

A 100 sqft adhesive-back mat with a touchscreen thermostat and an install monitor bundled in.

Best for: a first-time DIY install on a flat, solid subfloor Skip it if: you want the longest warranty on the market

VEVOR's mat targets the first-time installer. The mat is 1/8 inch thick with double-sided adhesive, laid at 2-inch spacing, and the listing says it stays flat once pressed to the subfloor. The included touchscreen thermostat has a stated range of 14 to 113°F, built-in GFCI, and an installation monitor that beeps if a cable is nicked mid-tile-set. That last item is genuinely useful. A cable break discovered after the mortar dries is a very expensive Saturday.

The trade-off shows up when you compare it to the BLARALA kit at the same 100 sqft coverage. VEVOR does not publish dual sensors or four operating modes on its thermostat, and the listing does not carry the same wet-location certification language BLARALA does. VEVOR does publish the tighter 2-inch spacing, which gives more even coverage on stone or thick tile. If you are heating a straightforward rectangular bathroom over a slab and you want the fastest path to warm tile, this is the kit that gets you there.

Pros:

• Adhesive-back mat installs quickly
• 2-inch spacing for more even heat
• Install monitor included
• Touchscreen thermostat with GFCI
• Detailed installation guide

Cons:

• No dual air-and-floor sensor
• No membrane or waterproofing layer
• No published warranty in the listing

5. Warming Systems - 15 Sqft Electric Radiant Floor Heating — Best budget pick

A 15 sqft cable-and-thermostat kit made in the USA, backed by a stated 25-year warranty.

Best for: a small entryway, powder room, or under-vanity zone Skip it if: you need to warm a full bathroom floor

This is the kit for the small job. Warming Systems ships 60 linear feet of cable at 180 W total, 12 W/sqft, sized for 15 sqft. Cable guides fix the spacing at roughly 3 inches. It is a loose cable, not a mat, so you supply the isolation layer, and coverage is capped at a small footprint: think in front of a vanity, a shower step, or a half-bath the size of a closet.

Two things make this the value pick. First, the bundled thermostat is the UWG5 touchscreen with WiFi and Bluetooth, the same OJ Microline platform the 50 sqft LuxHeat carries at a premium price position. Second, Warming Systems states the product is manufactured in Spring Grove, Illinois, and carries a 25-year warranty. That's the only stated warranty in this entire set. The trade-off is coverage. Fifteen square feet is the smallest zone here by a wide margin, so if you have a full bathroom to heat, look at the 100 sqft kits instead.

Pros:

• 25-year warranty, stated in the listing
• UWG5 WiFi and Bluetooth thermostat included
• Made in the USA
• 60 ft cable, 180 W at 12 W/sqft
• The cheapest of the five here

Cons:

• Only 15 sqft of coverage
• No membrane or mat included
• Loose cable takes longer to lay than a mat

Sizing your room without buying twice

The cost of getting sizing wrong is that you end up with a kit that covers 80% of the room and a cold strip of tile against one wall. You cannot splice two cables together to bridge a gap, and you cannot buy "the missing 8 sqft" as an add-on. So measure once, buy once.

• Heated area is not floor area. Subtract the vanity footprint, the toilet flange, the shower kerb, and a 3 to 4 inch perimeter along every wall.
• Round down, not up. A 60 sqft kit will not cover 61 sqft of heated area. Buy the next size up, or leave the last strip cold.
• Coverage densities are all 12 W/sqft here. So heating time and comfort are comparable across the five kits. What varies is the total wattage and amp draw, and those are what your electrician sizes the circuit against.
• Spacing changes coverage. A 200 ft cable at 3-inch spacing covers 50 sqft. The same cable at 4-inch spacing covers more area but at a lower watt density and a cooler floor.

For a typical 5x8 ft bathroom, subtract the vanity and toilet and you're often looking at 25 to 30 sqft of heated area. The 50 or 60 sqft kits give you routing slack. For a 6x10 bathroom, the 100 sqft mats become the honest match.

What the listings do not tell you

A few things every buyer asks and none of the listings answer clearly.

1. You cannot cut heating cable to length. The cable is a fixed resistance. Cutting it changes the load and destroys the kit. Mats can be cut between the cables to reshape the mesh, but the cable itself is off-limits.
2. Every one of these kits needs a dedicated line to a GFCI. Even though the thermostats have built-in GFCI, most local codes want the circuit itself sized for the heater. Confirm with an electrician before you buy tile.
3. Floor buildup matters. A membrane plus cable plus thinset plus tile can add 5/8 to 3/4 inch of height. That changes how your bathroom door swings and how your threshold meets the hallway floor.
4. None of these are primary heat. They are floor warmers. A 720 W kit is not sized to heat a room, only its floor surface. You still need the radiator or the HVAC on the coldest mornings.

The verdict

The 60 sqft LuxHeat kit is the pick I'd send most bathroom remodels toward, because the Prova Flex-Heat membrane does structural work beneath the tile that a bare mat cannot. Getting waterproofing, crack isolation and heated floor from one product simplifies the build-up and reduces the number of layers that can go wrong.

Two conditions flip the recommendation. If WiFi thermostat control is a hard requirement and your heated area is under 50 sqft, the LuxHeat 50 sqft runner-up brings the UWG5 head to the same membrane system. If you're heating 100 sqft and you want the faster install a mat provides, the BLARALA is the pro pick, and its dual air-and-floor sensor thermostat is genuinely the best-equipped head in this set. VEVOR is the beginner's version of the same 100 sqft mat idea, with a simpler thermostat and adhesive backing.

The Warming Systems 15 sqft kit sits outside the ranking in a useful way: it is the only one with a stated 25-year warranty, and it is the right buy for a small zone where a 60 or 100 sqft kit is wildly oversized. Skip it for full-bathroom coverage.

FAQ

Is electric radiant floor heating worth it?

Electric radiant floor heating is worth it in bathrooms, entryways and kitchens where cold tile is the daily discomfort. Every kit here delivers 12 W per square foot at 120 V, enough to keep tile pleasantly warm on cold mornings. It is not a replacement for a radiator or a heat pump, and the winning LuxHeat kit at 720 W will not heat a room by itself. Treat it as floor warming, not primary heat.

What size electric radiant floor heating kit do I need?

The size of electric radiant floor heating kit you need is smaller than your floor area suggests. Subtract the vanity footprint, the toilet base, the shower kerb and a 3 to 4 inch perimeter along every wall from the room measurement. A typical 5x8 ft bathroom often heats 25 to 30 sqft. The LuxHeat 50 or 60 sqft kits fit that with routing slack. A 6x10 bathroom is closer to the 100 sqft BLARALA or VEVOR mats.

Can I install electric radiant floor heating myself?

You can install electric radiant floor heating yourself if you are comfortable setting tile and can hire the electrical hookup. The mats from BLARALA and VEVOR are the fastest, with adhesive or mesh backings and included installation monitors that beep on a cable fault. The LuxHeat cable-and-membrane systems take longer because you weave cable through the Prova Flex-Heat membrane pockets. The thermostat connection itself needs a licensed electrician in most jurisdictions.

LuxHeat 60 sqft or BLARALA 100 sqft, which should I buy?

LuxHeat 60 sqft or BLARALA 100 sqft comes down to two questions: how big is your heated area, and does your subfloor need waterproofing? Choose LuxHeat if your heated area is 55 to 60 sqft and the floor is over wood framing or near a shower, because the Prova Flex-Heat membrane adds crack isolation and waterproofing. Choose BLARALA if your heated area is closer to 100 sqft on a solid subfloor and a faster mat install matters more.

Does electric radiant floor heating need a dedicated circuit?

Electric radiant floor heating usually needs a dedicated circuit, even on low-amp kits. The 60 sqft LuxHeat draws 6.0 A, the BLARALA mat draws 10.0 A, and every thermostat in this set has built-in GFCI protection. Local code typically still wants the branch circuit sized specifically for the heater, and the thermostat's Class A GFCI does not replace a properly rated circuit. Confirm with an electrician before you tile over anything.

If you're remodelling a bathroom this quarter and cold tile is the reason, the LuxHeat 60 sqft kit is the right default. The membrane it ships with earns its keep before the cable does, because waterproofing and crack isolation are things you'd have installed anyway under tile in a wet room. Buying them bundled with the heat means one supplier, one set of instructions, and one layer of buildup instead of three. Measure your heated area, subtract the fixtures, and match a kit to what's left. That is the whole decision.

Last updated: September 7, 2026. Product availability re-checked.

This page contains affiliate links. As an Amazon Associate we earn from qualifying purchases, at no extra cost to you.